Спасибо всем зрителям эфира! ❤

ok.ru/profile/566307918533/photos альбом на вегетативные растения для заказов.

Наш интернет-магазин – ogorod.net.ua/ семена, удобрения и многое другое для садоводов и огородников!
В этом видео расскажем об удобрениях, чем подкормить, с чего начинать и самые азы использования минеральных удобрений.
Это самые первые советы, конечно со временем нужно изучать больше и понимать больше. Это самое первое для начинающих.

Эксперимент по укоренению в перлите черенков. Черенкование роз в перлит, черенкование гортензии. Смотрим результаты.

In this project, we are converting a spare bedroom into a home office. Tile is an excellent choice for a home office because it’s easy to maintain, and the hard surface allows for easy the movement of office furniture that, more and more commonly these days, comes equipped with lockable rollers.

The tile that Teresa is installing in this segment is attractive porcelain tile from Dal-Tile. Porcelain is a great choice for a home office. Because porcelain tile is fired at very high temperatures, it’s denser and more durable than ceramic tile, and can better withstand the heavy use that’s typical in a home office. Porcelain tile is also very resistant to stains.

Step 1. The sub-floor of our house is a concrete slab. The first step is to remove the carpet and pad, then check the concrete floor for inconsistencies and rough spots. Dents and dings in the concrete will not pose as serious a problem for tile as will protrusions. If possible, chisel off any protrusions in the concrete that exceed an eighth of an inch. Then give the concrete a good cleaning.
(If the sub-floor beneath your tiling project is plywood or oriented strand board, plane down any high spots and re-nail the sub-floor in any places where the flooring has come loose.)

Step 2. Find the center of the room. To find the exact center of the room, measure the distance from one wall to the opposite wall, divided that number in half, and made a long perpendicular mark at that spot. She then repeated the process for the two other walls, and put an “X” where the two lines intersected. The same result can be achieved by striking chalk lines at the center points on opposing walls, and marking the point where the two chalk lines intersect.

Step 3. Then lay out a dry run of tiles from the center point to a facing wall, making sure to put spacers between the tiles. Measure the distance from the last tile to the wall, being sure to take into consideration the quarter inch of grouting that would fall between the last field tile and the border tile. If the distance between the last field tile and the wall is two inches or less, you should move the line of tile back toward the center of the room to ensure that the border tiles are not too narrow. This process ensures that the border tiles along this wall and the opposite wall are the same width. Then repeat the process along the other axis, toward the adjacent wall.
In this case, all border tiles needed to be cut at seven inches, resulting in border tiles measuring 12” X 7”.

Step 4. Teresa used a dry scoring tile cutter to cut all the border tiles. One can also use a wet saw, which can be rented from most big box home improvement stores. We were using a pattern that combined 12” X 12” tiles, 6” X 12” tiles and 6” X 6” tiles. To create the 6” X 12” tiles, Teresa simply cut the 12” X 12” inch tiles in half.

Step 5. Teresa bound the tiles to the floor using thinset mortar adhesive. There are many kinds of tile adhesive on the market, including pre-mixed compounds that come ready to spread. The thinset used came as a powder, and Teresa used an electric drill with a huge blender attachment to mix the powder with water until it was about the consistency of toothpaste.

Step 6. When the first batch of thinset mortar was ready, Teresa used a notched trowel to spread an even coat of thinset over the area she would begin to tile. She began the installation in the corner, first setting a square 7” X 7” tile, then began laying the other border tiles along both walls for a few feet.

Step 7. Next Teresa began laying the field tiles in the pattern we chose for this installation, spreading a section of thinset, then placing the tiles down in the pattern. She continued working in this fashion until the floor was completely covered in tile.

Step 8 It is extremely important to let the tiles set for a full 24 hours before applying the grout. Once the tiles have set for 24 hours, remove the spacers from between the tiles, and begin the grouting.

Step 9 For this project, we used a pre-mixed grout. Teresa spread the grout over the tile, making sure to push the grout down into the spaces between the tiles, not worrying too much about getting the grout onto the tile surface—there’s really no way to avoid getting grout on the tile surface while grouting, so it’s best just to concentrate on ensuring that the spaces between the tiles are filled.

Step 10. Although it’s tedious, it is necessary to sponge the grout off the top of the tiles soon after the grout is applied, using repeated passes with a sponge dipped in clean water. Because the grout is much harder to remove from tile after it has dried, it’s a good idea to grout only a small section at a time. A section five by five feet is about as large an area as can be adequately grouted before the grout begins to dry on the surface of the tile.

В этом уроке я учу, как повторно использовать стеклянные бутылки для изготовления цементных ваз в технике гранилит-бетон.

Хотели бы вы увидеть больше уроков?
Смотрите плейлист:
Бетонные искусства: www.youtube.com/playlist?list=PL4n9ZTkqfYqOjtIJfiZ76SUxf-zChbkDQ
Различные искусства: www.youtube.com/playlist?list=PL4n9ZTkqfYqNY9F0yM4M5-0ccqPCbYmFP
Рецепты макарон для поделок: www.youtube.com/playlist?list=PL4n9ZTkqfYqPPoObu0Cb5eEoG1meRi8tf
Растения: Выращивание и уход: www.youtube.com/playlist?list=PL4n9ZTkqfYqMu97a2J7nnol_JZGy60vA_
Цемент и бумага ручной работы: www.youtube.com/playlist?list=PL4n9ZTkqfYqMQ0u61rMLACL06K56O1h2u
Вазы из цемента и пенополистирола: www.youtube.com/playlist?list=PL4n9ZTkqfYqNHuyADjyP0FFjZZ6BkMHQe

Контакты в социальных сетях:
Instagram: www.instagram.com/mariaamelia.mendes/
Facebook: www.facebook.com/mariaameliamendes.vidaaudavelesustentavel/
Blogger: arterabiscoseletras.blogspot.com/
КОММЕРЧЕСКАЯ ПОЧТА: marmelia5@gmail.com

Спасибо!

This is a polymer finish putty diluted on PVA glue thick enough, as shown in the video.
Очень легко, быстро, красиво декорируем поверхность самыми простыми материалами. Всегда все есть дома.
Почта для связи makmarimak@mail.ru
В состав входит полимерная финишная шпаклевка густо размешанная на клее ПВА. Можно с добавлением воды.

В этой переделке «Дачный ответ» совместил две, казалось бы, совершенно разные культуры — японскую и скандинавскую. Для семьи Павлюкевич была сделана гостиная в стиле «джапанди», где переплетаются холодный камень и теплое дерево, «ленивые» диваны и танцующие журавли. Помимо этого, установлена удобная лестница, которая будто манит подняться по ней снова и снова. А заново прорубленные огромные окна качественно изменили фасад дома.

Яркие дизайнерские решения — в одном плейлисте:

www.youtube.com/playlist?list=PLSgy-gJ-dkS-UDf9fLAfnIJdfNjoQ2CpC

www.ntv.ru/video/click1867920/?catid=4

Сегодня я расскажу вам какими удобрениями я подкармливаю рассаду кустовой петунии, чтобы она хорошо развивалась и была красивой. Важно сделать ТРИ основные подкормки, без которых, добиться красивого цветения и хорошей рассады не получится.

У жителей южных регионов всё давно растёт и развивается, а у нас на севере посевы только начинаются. Но есть уже чему порадоваться и я предлагаю небольшой обзор рассады на 25марта.